Curing agent flooring

  1. What is a curing agent?

Cement ground curing agent is mainly composed of inorganic materials, silica and other calcium-silica compounds, is a colorless transparent, easy to use, non-toxic, non-flammable, highly permeable liquid material, the product through effective penetration, and concrete and stone building components of the chemical, crystallization reaction, so that the components of the concrete solidified into a solid entity, and blocked the concrete of the size of the pores, to get a dust-free dense whole, thus improving the abrasion resistance, compressibility, density and impermeability of concrete.

  1. Construction technical requirements

(1). A strength of c25 or greater (at least c20 or greater).

(2). The water-cement ratio shall not be higher than 0.4.

(3). The collapse of concrete mixed on site should be no greater than 5cm and the collapse of pumped concrete should be no greater than 12cm.

(4). For secondary poured concrete flooring, the thickness of the surface layer shall be not less than 5 cm.

(5). For better results, it is recommended that reinforcing mesh be added to the concrete.

(6). Concrete levelling plus or minus 1.5 cm, expansion joints can be divided according to the area of the workshop, as uniform as possible.

(7). 3 pulping and 3 mechanical lightening of the stock.

(8). The finish is smooth, with no knife marks on the ground, no trachoma, no honeycomb (more than 95% of the standard), no hollow drums, no delamination.

(9). Maintenance: Watered for 7 days.

(10). The formed concrete can be cured (hardened) in blocks for unlimited time, short cycle, flexible construction, and the ambient temperature is greater than 0 degrees can be normal construction.

  1. Construction process.

(1). Clean the floor and spray with sicaflor 4-1, soak for 1 hour, sand with 100# and 200#, and vacuum up any remaining stains. (requires that the rough and finish grain of the floor be sanded smooth).

(2). Spraying with sicaflor 4-1 and direct sanding with 500#, 1000# (or 2000#).

(3). Clean the residual stains, keep the floor moist and free from stagnant water, and spray scaf 4-2 in proportion, using black pads in two batches to wipe away evenly, with no smear marks .

(4). High-speed polishing with 1000# (or 2000#) after the floor is thoroughly dry.

  1. Evaluation of effectiveness

(1). Abrasion and pressure resistance, no sand or dust on the ground.

(2). No problem with how the forklift runs over it.

(3). High impact resistance.

(4). The strength and hardness of the ground have been greatly improved.

(5). With only one investment in construction, the life of the floor can be up to 30 years.

(6). The cost is lower than any kind of flooring, but the quality is better than any kind of flooring.

Epoxy resin paint flooring

  1. What is epoxy flooring?

Epoxy floor construction is the epoxy floor paint mixed and processed with epoxy resin main material, curing agent, diluent, solvent, dispersant, defoamer and some filler, epoxy floor construction has the advantages of strong acid and alkali resistance, abrasion resistance, pressure resistance, impact resistance, mold, waterproof, dustproof.

  1. Technical requirements of epoxy flooring.

(1). Epoxy flooring construction to the foundation concrete requirements: Concrete strength must be ≥ c25, including 350kg/m3 above ordinary silicate, cement and water-cement ratio <0.45.

(2). The deviation of flatness of the base layer should be less than 2mm.

(3). The water content of the grass-roots level should be less than 8%.

(4). The surface should be free of oil, debris, no obvious leakage.

  1. Epoxy flooring construction process

(1). Base treatment: Ground grinding, dense grass-roots level, clean the ground, polished smooth.

(2). Epoxy primer: Mix the epoxy resin and curing agent according to the correct ratio, use scraper or roller to apply coating method to seal.

(3). Mortar: Mix the epoxy resin and curing agent according to the correct ratio, and add some quartz sand according to the ratio; trowel open evenly according to the designed thickness, after the coating is dry, use sanding to grind the surface hangers and particles smooth.

(4). Epoxy putty: Mix the epoxy resin and quartz powder according to the correct ratio, then trowel on the surface evenly with the batch knife to increase the bond between the middle coat and the surface layer, and further adjust the smoothness of the surface. Depending on the actual number of times of construction, the flatness without cavities, without batch knife marks and sand grinding marks shall prevail.

(5). Epoxy topcoat: Mix the epoxy flooring topcoat material, mix evenly; add curing agent and mix, mix fully; use roller evenly coating, after the first coating dry solid, then construct the second topcoat, self-flowing plane coating with trowel hanging once.

  1. Benefit evaluation

(1). Thickness: The total thickness of the epoxy floor has an absolute effect on the unit price.

(2). Scale of the project: The scale of the epoxy flooring construction affects the quotation of the epoxy flooring.

(3). Epoxy resin paint material: Each layer of epoxy resin coating rate affects the unit price of epoxy flooring.

(4). The construction process of epoxy flooring: The number of epoxy flooring intermediate passes, grass-roots treatment requirements and other construction processes influence the quotation of epoxy flooring.

(5). Parts: Epoxy flooring construction and basements, tower stairwells, etc. All affect the quoted price of epoxy flooring.

 

(6). Brand: Epoxy flooring paint brand grade high and low affects the unit price of epoxy flooring.

Emery flooring

  1. Diamond sand flooring

Diamond sand flooring is the common name for wear-hardened flooring, which has the advantages of wear resistance and pressure resistance, dust reduction, hard surface, easy cleaning, economy and durability.

It is a pre-mixed, ready-to-use, dry-spreading ground hardening agent in the factory. It mainly consists of high-strength cement, inorganic wear-resistant aggregate, pigment powder (cement primary color without), additives and so on. Aggregate is sandy, with an average particle size of 1.5mm, accounting for about 60% of the total; cement is treated high-grade cement, in addition to the natural color of cement, there are red, yellow, green, gray and other colors to choose from.

  1. Construction technical requirements

The product is applied directly to the concrete at the initial setting stage or to the primary, curing agent floor.

  1. What is a curing agent?

Cement ground curing agent is mainly composed of inorganic materials, silica and other calcium-silica compounds, is a colorless transparent, easy to use, non-toxic, non-flammable, highly permeable liquid material, the product through effective penetration, and concrete and stone building components of the chemical, crystallization reaction, so that the components of the concrete solidified into a solid entity, and blocked the concrete of the size of the pores, to get a dust-free dense whole, thus improving the abrasion resistance, compressibility, density and impermeability of concrete.

  1. Construction technical requirements

(1). A strength of c25 or greater (at least c20 or greater).

(2). The water-cement ratio shall not be higher than 0.4.

(3). The collapse of concrete mixed on site should be no greater than 5cm and the collapse of pumped concrete should be no greater than 12cm.

(4). For secondary poured concrete flooring, the thickness of the surface layer shall be not less than 5 cm.

(5). For better results, it is recommended that reinforcing mesh be added to the concrete.

(6). Concrete levelling plus or minus 1.5 cm, expansion joints can be divided according to the area of the workshop, as uniform as possible.

(7). 3 pulping and 3 mechanical lightening of the stock.

(8). The finish is smooth, with no knife marks on the ground, no trachoma, no honeycomb (more than 95% of the standard), no hollow drums, no delamination.

(9). Maintenance: Watered for 7 days.

(10). The formed concrete can be cured (hardened) in blocks for unlimited time, short cycle, flexible construction, and the ambient temperature is greater than 0 degrees can be normal construction.

  1. Construction process.

(1). Clean the floor and spray with sicaflor 4-1, soak for 1 hour, sand with 100# and 200#, and vacuum up any remaining stains. (requires that the rough and finish grain of the floor be sanded smooth).

(2). Spraying with sicaflor 4-1 and direct sanding with 500#, 1000# (or 2000#).

(3). Clean the residual stains, keep the floor moist and free from stagnant water, and spray scaf 4-2 in proportion, using black pads in two batches to wipe away evenly, with no smear marks (drip marks on the material).

(4). High-speed polishing with 1000# (or 2000#) after the floor is thoroughly dry.

  1. Evaluation of effectiveness

(1). Abrasion and pressure resistance, no sand or dust on the ground.

(2). No problem with how the forklift runs over it.

(3). High impact resistance.

(4). The strength and hardness of the ground have been greatly improved.

(5). With only one investment in construction, the life of the floor can be up to 30 years.

(6). The cost is lower than any kind of flooring, but the quality is better than any kind of flooring.

Epoxy resin paint flooring

  1. What is epoxy flooring?

Epoxy floor construction is the epoxy floor paint mixed and processed with epoxy resin main material, curing agent, diluent, solvent, dispersant, defoamer and some filler, epoxy floor construction has the advantages of strong acid and alkali resistance, abrasion resistance, pressure resistance, impact resistance, mold, waterproof, dustproof.

  1. Technical requirements of epoxy flooring.

(1). Epoxy flooring construction to the foundation concrete requirements: Concrete strength must be ≥ c25, including 350kg/m3 above ordinary silicate, cement and water-cement ratio <0.45.

(2). The deviation of flatness of the base layer should be less than 2mm.

(3). The water content of the grass-roots level should be less than 8%.

(4). The surface should be free of oil, debris, no obvious leakage.

  1. Epoxy flooring construction process

(1). Base treatment: Ground grinding, dense grass-roots level, clean the ground, polished smooth.

(2). Epoxy primer: Mix the epoxy resin and curing agent according to the correct ratio, use scraper or roller to apply coating method to seal.

(3). Mortar: Mix the epoxy resin and curing agent according to the correct ratio, and add some quartz sand according to the ratio; trowel open evenly according to the designed thickness, after the coating is dry, use sanding to grind the surface hangers and particles smooth.

(4). Epoxy putty: Mix the epoxy resin and quartz powder according to the correct ratio, then trowel on the surface evenly with the batch knife to increase the bond between the middle coat and the surface layer, and further adjust the smoothness of the surface. Depending on the actual number of times of construction, the flatness without cavities, without batch knife marks and sand grinding marks shall prevail.

(5). Epoxy topcoat: Mix the epoxy flooring topcoat material, mix evenly; add curing agent and mix, mix fully; use roller evenly coating, after the first coating dry solid, then construct the second topcoat, self-flowing plane coating with trowel hanging once.

  1. Benefit evaluation

(1). Thickness: The total thickness of the epoxy floor has an absolute effect on the unit price.

(2). Scale of the project: The scale of the epoxy flooring construction affects the quotation of the epoxy flooring.

(3). Epoxy resin paint material: Each layer of epoxy resin coating rate affects the unit price of epoxy flooring.

(4). The construction process of epoxy flooring: The number of epoxy flooring intermediate passes, grass-roots treatment requirements and other construction processes influence the quotation of epoxy flooring.

(5). Parts: Epoxy flooring construction and basements, tower stairwells, etc. All affect the quoted price of epoxy flooring.

(6). Brand: Epoxy flooring paint brand grade high and low affects the unit price of epoxy flooring.

Emery flooring

  1. Diamond sand flooring

Diamond sand flooring is the common name for wear-hardened flooring, which has the advantages of wear resistance and pressure resistance, dust reduction, hard surface, easy cleaning, economy and durability.

It is a pre-mixed, ready-to-use, dry-spreading ground hardening agent in the factory. It mainly consists of high-strength cement, inorganic wear-resistant aggregate, pigment powder (cement primary color without), additives and so on. Aggregate is sandy, with an average particle size of 1.5mm, accounting for about 60% of the total; cement is treated high-grade cement, in addition to the natural color of cement, there are red, yellow, green, gray and other colors to choose from.

  1. Construction technical requirements

This product is constructed directly on the surface of concrete or cement mortar at the initial setting stage, forming a layer of hard, wear-resistant, dust-free and beautiful hardened floor after smoothing. Therefore, there must be a grass-roots leveling layer of concrete base requires a thickness of more than 50mm, intensity of not less than c25, site collapse 75-100mm.

  1. Construction process

Concrete control of base surface → first stage of material spreading construction → wiping → light → maintenance → cutting joints, filling.

(1). Concrete base surface should be dense, smooth, and no water secretion.

(2). The concrete should be tested by finger pressure when it is first set, leaving 3-5mm marks, and construction can be started.

(3). Spread the ground hardening material by hand, to be absorbed by the concrete moisture wetting can be used to compact and collect light with smoothing machine.

(4). Use manual trowel finish mechanical construction area.

(5). Do not splash water on the surface during the construction process.

(6). After the completion of the surface that is, with a special curing agent, with a fine mist spray construction maintenance, do not cover with plastic sheeting.

  1. Construction of economic benefits

The construction is simple and easy, directly spread on the initial concrete, saving time and labor, no need to construct the mortar surface layer; high abrasion resistance, reduce dust and improve the impact resistance. The surface of cement mortar, after smoothing, forms a layer of hard, wear-resistant, dust-free and beautiful hardened floor. Therefore, there must be a grass-roots leveling layer, the concrete base leveling layer requires a thickness of more than 50mm, intensity of not less than c25, site collapse 75-100mm.

  1. Construction process

Concrete control of base surface → first stage of material spreading construction → wiping → light → maintenance → cutting joints, filling.

(1). Concrete base surface should be dense, smooth, and no water secretion.

(2). The concrete should be tested by finger pressure when it is first set, leaving 3-5mm marks, and construction can be started.

(3). Spread the ground hardening material by hand, to be absorbed by the concrete moisture wetting can be used to compact and collect light with smoothing machine.

(4). Use manual trowel finish mechanical construction area.

(5). Do not splash water on the surface during the construction process.

(6). After the completion of the surface that is, with a special curing agent, with a fine mist spray construction maintenance, do not cover with plastic sheeting.

  1. Construction of economic benefits

The construction is simple and easy, directly spread on the initial concrete, saving time and labor, no need to construct the mortar surface layer; high wear resistance, reduce dust and improve the impact resistance.